Product Details
1. Product Introduction
The multifunctional forage grinder is equipped with a flywheel. When the main shaft speed reaches one revolution per minute, the flywheel can store enough energy to help assemble a smaller power ( Such as a single-phase, kilowatt motor) to complete the normal work of cutting grass and crushing.
2. Use and characteristics
This series of forage grass grinders can process orange stalks, cotton stalks, bean oranges, wheat oranges, pasture grass and other forage grasses as well as various grains. It can also crush corn cobs for planting flats. Used by friends who are interested in mushrooms and other practical fungi.
This series of forage grinders has the characteristics of cutting, kneading and crushing the grass into one. The new high-speed spray can throw the material - meters away when cutting the grass, which improves the shortcomings of the old model that requires frequent unloading.
This series of forage grinders has the characteristics of cutting, kneading and crushing the grass. It is an ideal equipment for large, medium and small farms and households to raise pigs, cattle, sheep, poultry, etc. for feeding.
3. Structure and working principle
The machine consists of an upper shell, a lower shell, a discharge port, a feed hopper, an angle steel frame, a hammer, a cutter, etc.
When crushing, the thickness of the crushed material is controlled by the size of the mesh, and different screens can be replaced.
When mowing alone, the screen can be pulled out.
4. Installation and debugging
The machine should be installed on a flat and solid site when working.
, Equip and install the motor according to the regulations.
Before installing the belt, you should first check whether the rotation direction of the index power is consistent with the cutting direction of the mower. After confirming that it is correct, adjust the installation belt and make the belt tight enough.
Before starting, the gap between the moving and fixed blades of the guillotine should be checked and adjusted so that the gap adjustment is controlled to be below .mm without collision, and then the bolts are tightened.
After all parts are adjusted normally and confirmed to be correct, turn on the power and do a test run. Check whether the fastener connections of each part are loose and whether there are any abnormal sounds in each rotating part.
6. Safe operation and maintenance
Before starting the machine, the operating instructions must be read thoroughly, and adjustments and maintenance must be carried out according to the instructions. The operator must understand the structure and functional requirements of the machine.
The supporting power must meet the requirements, and it is not allowed to increase the spindle speed without permission.
Before starting the machine, check whether the running direction is the same as the cutting direction, otherwise it is strictly prohibited to start the machine.
. Hard objects such as metal and stones must not be mixed into the materials that need to be cut, otherwise the machine will be damaged.
After the machine has been started for a few hours, it is necessary to observe whether the components are loose, and the bearings must be filled with grease regularly.
When feeding materials, the operator's hands must not be close to the blade to avoid personal injury. Feeding should be uniform and appropriate, not too much or too little, sometimes too fast and sometimes too slow.
It is strictly prohibited to operate under the influence of alcohol, illness, or excessive fatigue. It is strictly prohibited to wear gloves, mentally retarded persons, teenagers under the age of 18, senior citizens over 10 years old, and those who have not mastered the rules for using the mower.
During work, if weed blockage or other faults are found, the power should be turned off immediately and the fault should be eliminated before starting the operation. It is strictly forbidden to operate the machine while the machine is sick.
Non-staff members and those who are not familiar with the mechanism and performance of this machine are not allowed to turn it on casually.
When the machine is not used for a long time, it should be stored indoors or in a shed to prevent the machine from rusting.
. Machine technical parameters
Machine model:
Matching motor:
(
or
)
. Diesel engine:
/> Horsepower
. Rotor speed:
Machine output:
-
hour
(
The specific output depends on the size of the screen
)
Machine volume:
About
** ()
Machine weight:
Kilogram
(
This weight does not include the weight of the motor)< br/>
Disclaimer
The information/pictures/parameters, etc. displayed on this webpage about【New high-injection 400 type hay mower corn straw crusher/grass cutter/grass crusher/feed machine】are provided by member【Mr. Li
】,By Titker Trade Network members 【Mr. Li
】is solely responsible for the authenticity, accuracy and legality of the information/pictures/parameters, etc.,Titker Trade Network only provides display services. For your safety, please choose Titker Trade Network for online trading, otherwise Titker Trade Network will not bear any responsibility for this.
If your legitimate rights and interests have been infringed, please contact Titker Trade Network customer service as soon as possible. We will serve you wholeheartedly. Thank you for your attention and support to Titker Trade Network!