Year1
- 表干：
- 10~30
- 比重：
- 1.0~1.05
- 耐温：
- -50℃--250℃
)Typical uses
. Bonding, fixing and waterproofing of metal parts of small household appliances, silicon crystal plates, glass and plastics
.Casings and Fixing and sealing of base or heating parts
. Structural metal parts gap sealing, waterproof, air leakage prevention
) . ) ) . ) Factory direct sales, free trial samples for new customers, welcome to call us for consultation.
Bonding, fixing, sealing, electrical, insulation, moisture-proof, shock-proof, aging resistance and other properties.
,
The hardened silicone rubber can exert the original electrical properties of silicone and has good elongation at temperatures of ℃
~
℃
efficiency (it can maintain its original rubber elasticity despite vibration and impact), and has weather resistance, heat resistance, and cold resistance.
,
Can be firmly bonded to most materials such as metal, glass, ceramic tiles, plastics and their alloys.
, has good adhesion to a variety of metal and non-metal materials, and is completely non-corrosive to all metal and non-metal materials.
When the product is extruded from the packaging and comes into contact with moisture in the air, it begins to solidify and eventually forms an elastomer.
, heat resistance, cold resistance, adhesion and ease of operation
, superior electrical insulation properties and excellent chemical stability
, impact resistance and physical protection weather resistance (UV resistance, ozone resistance , water resistance)
, non-toxic, and silica gel has excellent physiological inertness.
) Scope of use
Widely used in bonding, fixing, sealing, electrical, insulation, antifouling, waterproofing,
shockproof, coating, etc. in electronic appliances, comprehensive small household appliances, instrument analysis, etc. application.
) How to use and precautions
According to the dosage, cut off the head of the nozzle head, install a special injection tool and extrude it before use,
cured at room temperature
, The sealing cap must be fastened after use.
When using, the adhesive layer must be fully exposed to the air. The larger the contact area, the faster the curing. Otherwise, it will slow down or even not cure.
The thicker the glue thickness, the longer the curing time, the higher the ambient temperature
(cannot be higher than
℃
), the greater the humidity, the slower the curing speed of the glue layer
/>The faster, otherwise the curing will be slower.
This product should be kept dry and protected from high temperatures during storage and transportation. The effective shelf life is
Clean the surface: Clean the surface of the adhered or coated object and remove rust, dust, oil, etc.
Apply glue and unscrew (or cut off) the cap of the hose, squeeze the glue onto the cleaned surface to make it evenly distributed, and close and fix the glued surface.
, Curing: Place the glued or sealed parts in the air and allow them to solidify naturally. The curing process is a curing process from the surface to the inside. Within hours (room temperature and % relative humidity) the glue will be cured to a depth of ~. If the glue is applied in a deep position, especially in parts that are not easily exposed to air, the time for complete curing will be If the temperature is low, the curing time will also be extended
After the operation is completed, the unused glue should be capped immediately and sealed. When using it again, if there is a little crust on the seal, just remove it and it will not affect normal use. During the storage process of the glue, a small amount of solidification may occur at the mouth of the tube. After being removed, it can be used normally without affecting product performance.
)Product packaging
Aluminum tube,
,
Plastic tube
.
) Main parameters
Model
Appearance of transparent paste fluid
Viscosity (.)
Specific gravity (℃).~
Surface drying time~
Shore hardness~
Elongation at break ( )~
Tensile strength ( /)~
Volume resistivity
Breakdown voltage/)~
Dielectric loss Angle tangent
High and low temperature resistance ℃~℃
Address 1st floor, Industrial Park Building, Sanlian Community, Longhua Street, Shenzhen
(This article is compiled and shared by Shenzhen Xingyongwei Thermal Silicone Co., Ltd.)
WhatsApp
