Yingtan hay crusher, grass crusher, feed straw crusher

1. Product Introduction
Guangzhou Huaxing Machinery’s functional forage grinder is equipped with a flywheel. When the spindle speed reaches one revolution per minute, the flywheel can store enough energy to help smaller power (such as single-phase kilowatts) motor) to complete normal mowing and crushing work.
2. Use and characteristics
This series of forage grass grinders can process orange stalks, cotton stalks, bean oranges, wheat oranges, pasture grass and other forage grasses as well as various grains. It can also crush corn cobs for planting flats. Used by friends who are interested in mushrooms and other practical fungi. This series of forage grinders has the characteristics of cutting, kneading and crushing the grass into one. When the new model is spraying the grass, it can throw the material a meter away, which improves the shortcomings of the old model that requires frequent unloading. It is an ideal choice for large, medium and small farms. The ideal equipment for raising chickens, ducks, pigs, cattle, sheep and other poultry in farms and households has small power, high output, simple structure, easy operation, can be operated by one person, has a wide range of processing, and the raw materials are not limited by length.
3. Technical parameters
Machine model
Wind angle plate/piece
Upper teeth/row
Bell blade/handle
Manganese steel blade/ Turn
Voltage/
Motor speed/
Rotor speed/
Machine output/hour (the specific output is determined according to the size of the screen)
Machine volume**
4. Structure and working principle
The machine consists of an upper shell, a lower shell, a discharge port, a feed hopper, an angle steel frame, a hammer, a cutting tool, etc.
When crushing, the thickness of the crushed material is controlled by the size of the screen holes, and different screens can be replaced.
When cutting grass alone, the screen can be pulled out.
5. Installation and debugging
The machine should be installed on a flat and solid site when working.
, Equip and install the motor according to the regulations.
Before installing the belt, you should first check whether the rotation direction of the index power is consistent with the cutting direction of the mower. After confirming that it is correct, adjust the installation belt and make the belt tight enough.
Before starting, the gap between the moving and fixed knives of the guillotine should be checked and adjusted so that the gap adjustment is controlled to be less than 1 meter without collision, and then the bolts are tightened.
After all parts are adjusted normally and confirmed to be correct, turn on the power and do a test run. Check whether the fastener connections of each part are loose and whether there are any abnormal sounds in each rotating part.
6. Safe operation and maintenance
Before starting the machine, the operating instructions must be read thoroughly, and adjustments and maintenance must be carried out accordingly. The operator must understand the structure and functional requirements of the machine. . The supporting power must meet the requirements, and it is not allowed to increase the spindle speed without permission.
Before starting the machine, check whether the running direction is the same as the cutting direction, otherwise it is strictly prohibited to start the machine.
. Hard objects such as metal and stones must not be mixed into the materials that need to be cut, otherwise the machine will be damaged.
After the machine has been started for a few hours, it is necessary to observe whether the components are loose, and the bearings must be regularly filled with butter.
When feeding materials, the operator's hands must not be close to the blade to avoid personal injury. Feeding should be uniform and appropriate, not too much or too little, fast and slow.
It is strictly forbidden to operate after drinking, being sick, or overtired. It is strictly forbidden to wear gloves, mentally retarded people, teenagers under the age of 10, senior citizens over 10 years old, and people who have not mastered the rules for using the mower. It is strictly prohibited to operate alone.
. During work, if weed blockage or other faults are found, the power should be turned off immediately, and the fault should be eliminated before starting the operation. It is strictly forbidden to operate the machine with a disease.
Non-staff members and those who are not familiar with the mechanical performance of this machine are not allowed to turn it on casually. . When the machine is not used for a long time, it should be stored indoors or in a shed to prevent the machine from rusting.
Note that for this machine, the crushing fineness is determined by the size of the sieve holes. Users can choose the screen reasonably according to the particle size requirements of the feed.