Year1
- 型号：
- PL-6000A
- 除尘率：
- 99.9（%）
1. Drawer-type single-machine bag dust collector with ash hopper
Product Introduction Series single-machine dust removal equipment is an improvement on the dust removal equipment introduced from abroad. The novel product successfully developed is an on-site dust removal unit with small size and high dust removal efficiency.
2. Structural Overview
Drawer-type single-machine bag dust collector with ash hopper
The basic structure of the unit consists of three parts: fan, filter and dust collector. Each component is installed in a Inside the vertical frame, the steel plate shell has beautiful appearance, scientific structure, reliable operation and easy use.
The structural characteristics of each component of the drawer-type single-machine bag dust collector with ash hopper are as follows
The machine components are imitated foreign centrifugal fans, with large air volume, high air pressure, hard fan characteristic curve, and Adopting noise reduction measures, the noise is low during use.
The filter component of the ash hopper drawer-type single-machine bag dust collector
The filter component uses industrial polyester cloth as the filter material and a flat cloth bag filter. The cloth bag is equipped with a spring steel mesh, which has good filtration effect and is easy to replace the filter bag. long lasting.
The dust cleaning mechanism of the filter component uses a motor to drive the eccentric wheel, and the connecting rod shakes the bag to remove dust stuck to the outer surface of the filter bag. The control device is divided into two types: automatic control and manual control. Automatic control means that when the fan is working continuously, the dust cleaning mechanism will automatically vibrate and clean the dust at regular intervals. Manual control means that the dust cleaning mechanism will automatically work after the fan stops and will automatically stop after dozens of seconds. You can also start the dust cleaning motor to vibrate and clean at any time as needed. The user can adjust the time relay for dust cleaning time.
The filter component is equipped with a wide and sealed quick-detachable access door② to facilitate inspection and removal of the filter when necessary.
The air inlet interface ③ on the upper side of the dust collector can be folded down when needed to increase the use of the air inlet area.
Ash hopper drawer-type single-machine bag dust collector
There are sixteen specifications, divided into two types. The model is equipped with a ash hopper drawer, and the model is not equipped with a ash hopper drawer. The lower flange is directly connected by the user to the dumping port of the folding bin, the mixing bin, sandblasting box, belt transport U-turn and other dust-raising equipment for on-site dust removal, and the dust is directly recovered.
3. Drawer-type single-machine bag dust collector with ash hopper
Working principle
Dust-containing gas enters the box and is filtered by the flat bag filter, and the dust is blocked on the outer surface of the filter bag , the purified gas enters the fan through the filter bag, and is sucked in by the fan and discharged directly into the room (it can also be discharged to the outside via a pipe).
As the filtration time increases, the dust attached to the outer surface of the filter bag also increases, and the resistance of the filter bag also increases accordingly, thus affecting the dust removal effect. An automatic dust cleaning mechanism is used for regular vibration cleaning or manual cleaning. After the dust mechanism stops, it will automatically vibrate for tens of seconds to shake off the dust stuck to the outer surface of the filter bag. The dust falling into the dust collection container (drawer) is manually pulled out and removed.
4. Drawer-type single-machine bag dust collector with ash hopper
Uses
Drawer-type single-machine bag dust collector with ash hopper
Widely used in foundry industry, ceramic industry, glass industry Industrial and dust removal in refractory materials, cement building materials, sand fiber manufacturing, chemical products, mechanical processing and other industries. Drawer-type single-machine bag dust collector with ash hopper is suitable for metal chips with large specific gravity, foundry sand, such as lathes, grinders, milling machines, grinders, polishers, etc., and dust with medium specific gravity, such as cement, ceramic powder, and gypsum powder. , toner, pigments, bakelite powder, plastic powder, etc., as well as non-fibrous dust with a lighter specific gravity, all have good dust removal effects. The dust removal efficiency of this unit is greater than 99.5%.
The injection pressure, that is, the machine vacuum, refers to the pressure available for the machine, which is the absolute value of the measured static pressure at the air inlet of the machine
The injection efficiency is greater than the talcum powder used for the determination of the median diameter. Value, the lowest measured value is, the average value isbr/> The air volume of the device is the suction volume at the operating pressure
5. Instructions for use of series single-machine bag dust collector
Ash hopper drawer-type single-machine bag dust collector
When installed near mechanical equipment that generates dust, the user can prepare metal or plastic vacuum ducts and dust hoods according to the size of the air inlet on the dust removal group (you can also contact the manufacturer when ordering) can be prepared on your behalf).
Before starting work, check whether the access door, dust outlet door and air duct connection system are sealed to avoid leakage and reduce the dust collection effect.
The voltage of the ash hopper drawer-type single-machine bag dust collector is three-phase AC 380 volts. It can be used after connecting the power supply to the external wire on the unit. During initial operation, you should pay attention to whether the fan is rotating forward ( If it is reversed, the air volume will be very small, and the power wiring needs to be changed).
The cover of the electrical control box should not be opened at will during work. If you need to adjust the cleaning time or check the circuit, you should stop the machine or cut off the power before starting work.
According to the nature of the dust and the size of the dust-holding capacity, the dust should be regularly vibrated and cleaned. Generally, the vibrating should be done three to four times per shift, and it is appropriate to vibrate for seconds each time to ensure the normal operation of the unit.
According to actual needs, clean dust regularly. When cleaning the dust in the dust collector, you only need to open the sealed dust outlet door and pull out the drawer when the fan and dust cleaning mechanism stop working.
In order to ensure that the equipment is in the best working condition, it should be as close as possible to the source of dust. Generally, the connecting pipe should be one and a half to two meters long, which may be shorter, and elbows should be minimized to avoid increasing resistance loss.
The dust cover is a key accessory to ensure that the unit is in optimal condition. The user should design and manufacture the dust cover based on the dimensions of the workpiece and the nature of the dust, and in accordance with the principles of accessibility, proximity, smoothness, sealing and convenience. Ideal vacuum hood.
6. Maintenance of drawer-type single-machine bag dust collector with ash hopper
The bag filter should be checked for wear regularly. If any damage is found, the filter should be repaired or replaced in time. At the same time, the bag filter should be checked regularly for wear and tear. Clean the dust bag regularly according to the actual situation. Generally, it needs to be cleaned once every four months of continuous use. When cleaning or replacing, you only need to loosen the four tightening screws of the filter component to pull it out. When reinstalling, pay attention to the seal between the filter component and the fan component (there is a sealing packing between the two components). At the same time, pay attention to whether the bag partition under the filter component is aligned with the flat cloth bag. After installation, the machine should be turned on and shaken several times. , so that the filter can restore its original filtration efficiency.
Generally, every other month, fold down the vibration cleaning motor cover, add butter to the eccentric sleeve bearing, and check whether the rubber sealing film is damaged. If it is worn and damaged, replace it.
The unit should be wiped, cleaned and inspected frequently to keep it clean and beautiful to ensure normal operation of the unit.
Damaged parts can be reported by phone, mail or purchased in person, and the factory will pay immediately.
7. Precautions for series single-machine bag dust collectors
Ash hopper drawer-type single-machine bag dust collectors
are not suitable for moist and corrosive dust-containing gases. It is not advisable to inhale gas with a temperature above 100 degrees for a long time.
If there is any abnormality during the start, stop and operation of the unit, the work should be stopped immediately for inspection and repair.
The machine should press the stop button to let the rapping mechanism work for tens of seconds, and should not directly pull down the power switch to stop the machine.
When purchasing air box pulse dust collectors, Hebei Xinda Dust Removal Equipment Co., Ltd. is your first choice. We will use the highest quality products and the most affordable prices to look forward to your visit!
Botou City direct sales drawer type single machine bag dust collector with ash hopper
WhatsApp
