Year1
- 功 率：
- 0.37KW～55KW
- 转 矩：
- 150N·m～20000N·m
- 单级：
- 7-87
. Cycloidal reducer
Cycloidal pinwheel reducer adopts cycloid pintooth meshing and planetary transmission principle. This kind of reducer can be widely used as the reduction mechanism in various transmission machinery such as heavy transportation, mining, metallurgy, petrochemical industry, food, pharmaceutical, textile printing and dyeing, etc.
Conditions for use of planetary cycloidal pin wheel reducer
Planetary cycloidal pin wheel reducer is allowed to be used in continuous working conditions, and is allowed to run in both forward and reverse directions at the same time.
The rated speed of the input shaft is rpm. When the power is greater than .kW, rpm is used.
The working positions of cycloidal reducers and cycloid reducers are all horizontal. When used at an angle, the maximum inclination angle is generally less than. When exceeded, other measures should be taken to ensure adequate lubrication and prevent oil leakage.
. The output shaft of the reducer cannot be subject to large axial force and radial force. When there is large axial force and radial force, other measures must be taken.
Technical parameters
Power
,~
Torque?~?
Transmission ratio
Single stage
Double stage
Three-stage
, series of cycloidal pinwheel reducer products have the following characteristics, multi-tooth simultaneous meshing transmission, strong overload resistance and high reliability. . The main transmission parts are made of bearing steel and have been quenched and ground. It has high-strength design, is sturdy and durable, and has a long service life. , small inertia, suitable for frequent starts and forward and reverse rotation. , low noise and high efficiency, the first-level deceleration can reach more than %. , Compact structure, coaxial output.
, Structural Principle Planetary transmission, using the internal meshing of the cycloidal wheel and the pin teeth to form an internal meshing reduction mechanism with a small tooth difference, which transmits the input speed coaxially in the reverse direction and performs deceleration.
, Features adopt planetary transmission principle, small size, no axial force, large speed ratio change range
, Installation type, base type, flange type, output mode, solid shaft output, input mode, motor input, shaft input
/> , input mode direct motor, solid shaft, flange input.
, average efficiency level 1%, level 2 %.
Instructions for the use and lubrication of cycloidal pinwheel reducer
(1) Use
. This machine is suitable for continuous working system and allows forward and reverse operation
. The output shaft rotation of the single-stage reducer is opposite to the input shaft rotation, and the output shaft rotation of the double-stage reducer is the same as the input shaft rotation. The output shaft rotation of the three-stage reducer is opposite to the input shaft rotation
. The output shaft of this reducer cannot bear axial force
. When the output shaft and input shaft are matched with other parts, direct hammering is not allowed to prevent damage
. The keys on the output shaft and input shaft extension are selected according to the ordinary flat key type rule (). The fit tolerance value of the base diameter of the vertical reducer output end meets the limit and fit () rules
. When using a coupling, the axis of the working machine and the motor should be connected concentrically, and the installation error of the reducer should not be greater than the allowable error value of the coupling used.
2) Lubrication
． This machine mainly uses oil bath lubrication
Suitable for ambient temperatures from 100°C to 100°C, lubricating oil is used when the ambient temperature ranges from 10°C to 10°C. When installed at an angle, grease lubrication can be used. Types and above all have circulating lubrication. Before driving, start the oil pump micromotor. It depends on whether the oil pump supplies oil. Otherwise, the micromotor wiring should be commutated. Since the oil pump runs in the specified direction, the oil level should be maintained after the oil pump is in normal operation. At the center line of the circular oil mark, there is a sealing ring at the end face connection between the oil pump and the reducer to prevent leakage and oil leakage.
Installation of Planetary Cycloidal Pinwheel Reducer
When installing couplings, pulleys, sprockets and other connecting parts on the output shaft of the cycloidal reducer, direct hammering is not allowed, because the The output shaft structure of the reducer cannot withstand axial hammering force, so screws can be screwed into the screw holes at the shaft end to press into the coupling.
The shaft diameters of the output shaft and input shaft should be matched.
The lifting eye screws on the cycloidal reducer are only for lifting the reducer.
Factory address Liying Industrial Park, Rencheng District, Jining City, Shandong Province
Consultation phone number
Online
WhatsApp
