Ceramic tube 15G ozone generator high concentration water treatment ozone machine accessories

Ceramic tube/ozone generator accessories power supply + tube are a set.
The normal service life is up to more than 10 years, and the whole set is purchased with a free 1-year warranty
(except for man-made damage or damage caused by incorrect installation and use).

or
, please pay attention to the working voltage!
The color of the heat sink of the ozone tube may vary slightly due to different batch production. The quality is the same.
Technical parameters
Product model
Use gas source
Oxygen, or air/.
Maximum ozone concentration
/(oxygen/hour)
Maximum ozone production
/(oxygen flow rate/hour)
Working environment requirements
Ambient humidity is less than The ambient temperature is less than degrees Celsius, and it is a dry, clean and well-ventilated environment.
Ozone tube size
**
Cooling method
Internal water cooling + external air cooling
Power supply size
**
Input power supply
/ or / two different voltages, please choose carefully.
Output power
～ (can be continuously adjusted)
Output voltage
(effective value)
Operating frequency
～ ((can be continuously adjusted)
Power supply features
, push, bandwidth automatic/manual,
, power-on slow start, (limit surge current)
, power supply over-voltage protection
, power converter overheating protection , output short circuit, open circuit protection, sound and light warning
, circuit anti-interference, moisture-proof, anti-corrosion design.
Features of Taisheng Technology Ceramic Tube Ozone Generator
High efficiency using narrow gap discharge, ozone conversion High efficiency and low noise.
Low power consumption, high voltage and high frequency corona discharge, power consumption rate~
Small size, effective in saving volume. Compared with the output products, Taisheng Technology ceramic ozone unit is small in size.< br/>The working voltage of the non-breakdown generating tube is only its breakdown voltage and high dielectric constant.
The high-quality dielectric material is sintered at high temperature using imported high-purity alumina ceramics, and is polished with high precision inside and outside for secondary processing and discharge. Uniform, stainless steel internal electrodes and fasteners, PTFE gas nozzles, corrosion-resistant high-purity fluorine rubber ring seals, external air-cooling and heat dissipation using the latest Sunflower aluminum alloy heat dissipation technology, effective heat dissipation, long-term operation with ultra-low ozone attenuation <, The service life is long, up to 20,000 hours.
Analysis of the internal structure of the ozone tube
Shipping instructions
We will only confirm the accuracy after multiple tests after the buyer takes the photo. Packaged and shipped, when leaving the factory, the internal adjustment of the power supply has been fully debugged, and all parameters have reached the best performance value. Buyers should not adjust the internal adjustability easily.
After the equipment is installed, the external potentiometer can be adjusted at will Adjust, adjust clockwise until the maximum ozone output is the maximum value, and vice versa.
Notes
When the ozone generator (ozone tube) works continuously for a long time (single use exceeds minutes), internal water cooling is required. , external air cooling. As long as the accessories are installed correctly, the water cooling and air cooling are appropriate, and the air source is stable, the product can work continuously for hours and days. The service life can be up to years. It cannot be used in flammable and explosive environments.
About installation
The ceramic tube and high-voltage power supply are installed on the insulating board, with a distance above the distance between them. The positive electrode of the high-voltage wire is connected to the heat sink, and the ground wire is connected to the water cooling nozzle or the bracket. Do not merge the two high-voltage wires together. Keep the distance above the distance. The insulation board is fixed inside the chassis. Other non-high-voltage wires cannot be close to places with high voltage. Above the distance, other working instruments (ammeters, voltmeters, digital control terminals) cannot be close to high-voltage places. High voltage will interfere with the instrument. Normal value, the distance is greater than. The chassis needs to have two vents, one of which is equipped with a fan. The wind blown into the chassis by the fan must be able to blow to the heat sink of the ceramic tube. The other vent is used to exhaust air. The flow rate of water cooling is greater than / .
The two air nozzles on the pipe, regardless of air inlet or air outlet, can use oxygen as the gas source or air as the gas source. If oxygen is used, the flow rate is / is enough, and the output can be as high as / Around /, the highest concentration can reach /. If air is used, the flow rate should be between / (choose an air compressor pump with a flow rate of / and use an air source. If possible, you can add a drying filter equipment, which can protect the ozone tube. The service life can also increase the ozone concentration. If you need to purchase a filter dryer, we can supply it
Ceramic tube high concentration water-cooled power supply illustration
Welcome to consult Deng Zhiren