Aolitai general waterproof slurry (two-component) kitchen, bathroom, balcony, garage waterproofing project waterproofing

This product is a two-component cement-based acrylic polymer waterproofing product. The active ingredients in the slurry can penetrate into the capillary pores and micro-cracks of the substrate to form a crystalline and dense waterproof layer. It has the characteristics of both rigidity and softness. It not only has the extensibility and waterproofness of polymer coatings, but also has the advantages of hydraulic cementitious materials with high strength, good water resistance, and easy bonding with wet base layers. [Product Features]
●Strong adhesion, effective in waterproofing both upstream and backside surfaces.
●A tough waterproof membrane integrated with the base surface can cover micro-cracks in the base.
●Wide range of application, can be used for waterproofing projects on various base surfaces.
【Scope of application】
●Especially suitable for waterproofing and moisture-proofing in kitchens and bathrooms.
●Suitable for underground parking lots, retaining walls, edible pools, and waterproofing projects.
【How to use】
◆ Base surface treatment
The base surface should be solid, flat and clean. Obvious pores should be blocked and smoothed with cement mortar. Before construction, wet the base surface until there is no clear water. .
◆ Mixing and Stirring
Pour the emulsion into the container according to the ratio of powder to liquid, stir it slightly, then slowly add the powder, stir thoroughly with a low-speed electric mixer, let it sit for ~ minutes, and then add a little more It can be used after stirring. Intermittent stirring should be maintained during use to mix the glue evenly and prevent precipitation.
◆Construction method
Use a brush or roller brush to apply the paint on the base surface. The thickness should be applied in batches according to the construction requirements. The thickness of a single session should not exceed. The interval between each application is ~ hours (adjust appropriately depending on changes in temperature, humidity, etc. at the construction site, and should be extended in winter), and the paint should be applied in the vertical direction to ensure that no brushing is missed.
◆ Post-processing
It is forbidden to step on the waterproof layer within hours after the construction is completed. The next process can only be carried out after it is completely dry. Pools that have been filled with water for a long time should wait for a few weeks before they can be filled with water. Pools with hot water or corrosive liquids will need a few weeks.
[Reference dosage]
●When the base surface is flat and the thickness of the waterproof layer is , the dosage is approximately ./~./.
[Notes]
◆
It is not recommended to use this product in the following situations: Waterproofing projects with base material cracks exceeding seams, settlement joints, post-casting tapes, sealing of wall pipes, etc.
◆
The suitable temperature for construction is in the range of ℃~℃. It is not suitable for construction in rainy weather or when there is open water on the base layer.
◆
In places where the air is particularly humid and there is no ventilation, ventilation equipment should be used to speed up the drying of the waterproof coating. Otherwise, the surface of the film may turn white after it dries, but this does not affect the waterproof performance.
◆
This product is weakly alkaline and will irritate the skin. Necessary protective measures should be taken during use.
【Executive Standards】
This product implements the technical requirements of the standard/medium type.
[Storage and Transportation]
◆
This product should be stored off the ground on a pallet in a ventilated and dry place. It should be protected from rain and moisture, and should be prevented from overlapping layers, otherwise the product may be damaged. Premature failure. During transportation, they should be protected from the sun, rain and cold, be carefully stacked, and pay attention to prevent packaging damage.
◆
Store in a cool and dry place. The shelf life of unopened products is one month.
[Statement]
Our company guarantees that the quality of manufactured products complies with relevant national requirements and specifications, but does not assume any responsibility for direct or indirect losses caused by incorrect use of this product by users.
If you have any questions, please consult the company's technical department or our local dealer.