Aolitai Leak Stopping Kitchen, Bathroom, Balcony, Garage and Basement Waterproof Leak Stopping King Manufacturer

This product is a new type of rigid, quick-acting waterproofing and leak-stopping material. Its characteristics are that it sets and hardens quickly, the time interval between initial and final setting is extremely short, and it quickly develops strength after final setting. It can operate with water and quickly stop water and leaks. It is especially suitable for crack treatment in kitchen and bathroom, treatment of defects around pipe openings and quick repair of defects. 【Product Features】
●Quickly hardens and stops water instantly.
●High early strength and good adhesion to the base layer.
●Non-toxic and odorless, can be used in drinking water projects.
●Waterproof, moisture-proof, anti-seepage, long-term water resistance.
[Scope of application]
●Suitable for rapid repair and reinforcement projects of non-scalable concrete or mortar structures in kitchens and bathrooms, basements, and roofs.
●Repair of defects around various wall pipes and yin and yang corners.
【Usage】
◆ Ingredients
Configure leakage plugging and yin and yang angle treatment according to the ratio of powder to water as needed. After adding water and powder into the container in proportion, stir quickly and evenly. The number of ingredients at one time should not be too large to avoid wasting materials due to solidification.
◆ Construction methods for plugging leaks
Cut out the concrete or masonry around the leak or crack at least wide and deep, and chisel the hole or crack into shape to ensure that it forms a good structure after final curing. bonding. Rinse or blow away all loose particles, dust and debris from the treated surface, and thoroughly wet the area to be repaired. If there is serious water seepage on the base surface, a water canal should be built to drain the leaking water together so that there is no obvious water leakage from the original leaking water base surface.
◆ Construction methods for seepage surface treatment
The base surface should be moist, firm and clean. Rough and uneven areas can be leveled by mixing this product with twice the weight of medium sand. The construction is carried out in several steps. Quickly apply the first layer of material with the prepared slurry on the base surface with exposed water. After the first layer hardens (no trace of finger pressure), wipe away the surface water marks and scrape and apply the second layer. If there is still a large area of water seepage, apply the third layer of material. If there is only local water seepage, apply another layer of material at the seepage area until the blockage is stopped. When applying each layer, you must scrape it back and forth with a little force. times, so that the coatings are densely covered, and the material used for each layer is about . The total thickness is about .~.
◆ Post-maintenance
The curing time is ~ days, and the methods include sprinkling water, covering with moisture, and curing with curing solution. In a humid environment such as a basement with accumulated water, or if a protective layer or material is applied immediately after the waterproof layer hardens, wet curing is not required.
【Notes】
◆
The moisture ratio can be adjusted appropriately depending on the substrate, weather, and construction conditions
◆
The condensation time may vary depending on the amount of water used. , Fluctuations due to different construction temperatures
◆
After this product is opened, in order to avoid product performance being affected, unused products should be resealed
◆
A large amount will condense when condensing. If it generates heat, be careful to avoid burns
◆
This product is highly alkaline, so appropriate protective measures should be taken during construction
◆
It is best to use it up at once after opening the package, or seal it well Store in a dry room
◆
When the temperature is lower than ℃, it is advisable to stir with warm water greater than ℃.
【Executive Standards】
This product complies with the technical requirements of the national standard medium-speed setting type (type).
[Storage and Transportation]
◆
This product should be stored in a ventilated and dry place and should be protected from rain and moisture, otherwise the product may fail prematurely. During transportation, they should be protected from the sun, rain and cold, be carefully stacked, and pay attention to prevent packaging damage.
◆
Store in a cool and dry place. The shelf life of unopened products is one month.
[Statement]
Our company guarantees that the quality of manufactured products complies with relevant national requirements and specifications, but does not assume any responsibility for direct or indirect losses caused by incorrect use of this product by users.
If you have any questions, please consult the company's technical department or our local dealer.