Aolitai full-effect waterproof mortar (two-component) kitchen, bathroom, balcony, basement, interior and exterior wall waterproofing

This product is a two-component polymer cement-based waterproofing product. After construction, its active ingredients can penetrate into the capillary pores and micro-cracks of the base material to form a crystalline and dense waterproof layer. With the combination of rigidity and softness, it has full and excellent waterproofing effect whether it is the interior or exterior walls of buildings, pools, basements, etc. It is especially suitable for interior and exterior wall waterproofing projects with exterior finishes. [Product Features]
●Wide range of application, can be used for waterproofing projects on most solid cement mortars and concrete base surfaces.
●It can be brushed, rolled or sprayed with a spray machine. It has super strong adhesion and can firmly bond to wet base surfaces and various types of decorative tiles.
●Cold construction, easy operation, short drying time, can shorten the construction period.
【Scope of application】
●Especially suitable for waterproofing engineering treatment of interior and exterior walls with exterior facings.
●Suitable for waterproofing and moisture-proof treatment of kitchens, bathrooms, balconies, basements, retaining walls, and drinking water pools.
[Construction Technology]
◆ Base surface treatment
The base surface should be solid, flat, and clean. Obvious pores should be blocked and smoothed with cement mortar. Before construction, the base surface should be moistened until there is no clear water. .
◆ Mixing and Stirring
Pour the emulsion into the container according to the ratio of powder to liquid, stir it slightly, then slowly add the powder, stir thoroughly with a low-speed electric mixer, let it stand for ~ minutes, and then add a little It can be used after stirring. When using, keep stirring intermittently to make the glue evenly mixed and prevent precipitation.
◆Construction method
Use a brush or roller brush to apply the paint on the base surface. The thickness should be applied in batches according to the construction requirements. The thickness of a single session should not exceed. The interval between each application is ~ hours (adjust appropriately depending on changes in temperature, humidity, etc. at the construction site, and should be extended in winter), and the paint should be applied in the vertical direction to ensure that no brushing is missed.
◆ Post-processing
It is forbidden to step on the waterproof layer within hours after the construction is completed. The next process can only be carried out after it is completely dry. Pools that have been filled with water for a long time should wait for a few weeks before they can be filled with water. Pools with hot water or corrosive liquids will need a few weeks.
[Reference dosage]
●When the base surface is flat, the thickness of the waterproof layer is , about ./~./.
[Notes]
◆
It is not recommended to use this product in the following situations: Waterproofing projects with base material cracks exceeding seams, settlement joints, post-casting tapes, sealing of wall pipes, etc.
◆
The suitable temperature for construction is in the range of ℃~℃. It is not suitable for construction in rainy weather or when there is open water on the base layer.
◆
In places where the air is particularly humid and there is no ventilation, ventilation equipment should be used to speed up the drying of the waterproof coating. Otherwise, the surface of the film may turn white after it dries, but this does not affect the waterproof performance.
◆
This product is weakly alkaline and will irritate the skin. Necessary protective measures should be taken during use.
[Storage and Transportation]
◆
This product should be stored off the ground on a pallet in a ventilated and dry place. It should be prevented from being soaked by rain and moisture, and should be prevented from overlapping layers, otherwise the product may be damaged. Premature failure. During transportation, they should be protected from the sun, rain and cold, be carefully stacked, and pay attention to prevent packaging damage.
◆
Store in a cool and dry place. The shelf life of unopened products is one month.
[Statement]
Our company guarantees that the quality of manufactured products complies with relevant national requirements and specifications, but does not assume any responsibility for direct or indirect losses caused by incorrect use of this product by users.
If you have any questions, please consult the company's technical department or our local dealer.